Letter Drill Bit Sizes
Letter drill bits run from A (0.234 in) to Z (0.413 in), with the larger letter being the larger bit.
Last verified October 5, 2026
Closest bits
0.1990 in (5.05 mm), 0.0010 in under 0.2000 in
Letter drill bit sizes, A to Z
Each size with the screw threads that use it as a 75% tap drill.
| Size | Decimal (in) | Millimeters | 75% tap drill for |
|---|---|---|---|
| A | 0.2340 | 5.94 | — |
| B | 0.2380 | 6.04 | — |
| C | 0.2420 | 6.15 | — |
| D | 0.2460 | 6.25 | — |
| E | 0.2500 | 6.35 | — |
| F | 0.2570 | 6.53 | 5/16-18 UNC |
| G | 0.2610 | 6.63 | — |
| H | 0.2660 | 6.76 | — |
| I | 0.2720 | 6.91 | 5/16-24 UNF |
| J | 0.2770 | 7.04 | — |
| K | 0.2810 | 7.14 | — |
| L | 0.2900 | 7.37 | — |
| M | 0.2950 | 7.49 | — |
| N | 0.3020 | 7.67 | — |
| O | 0.3160 | 8.03 | — |
| P | 0.3230 | 8.20 | — |
| Q | 0.3320 | 8.43 | 3/8-24 UNF |
| R | 0.3390 | 8.61 | — |
| S | 0.3480 | 8.84 | — |
| T | 0.3580 | 9.09 | — |
| U | 0.3680 | 9.35 | 7/16-14 UNC |
| V | 0.3770 | 9.58 | — |
| W | 0.3860 | 9.80 | — |
| X | 0.3970 | 10.08 | — |
| Y | 0.4040 | 10.26 | — |
| Z | 0.4130 | 10.49 | — |
How to use this chart
Letter bits fill the gaps between larger fractional bits, from 0.234 to 0.413 inch. Find the letter, then read the decimal inch and millimeter size. The last column shows the thread the bit taps at 75%, such as F for 5/16-18 coarse.
Frequently asked questions
What size is an F drill bit?
An F bit is 0.2570 inch, or 6.53 mm. It is the tap drill for a 5/16-18 coarse thread.
Is a Z drill bit bigger than an A?
Yes. Letter bits increase from A at 0.234 inch to Z at 0.413 inch.
What is the letter drill bit for a 1/4 inch hole?
The E bit is 0.2500 inch, the same as a 1/4 inch fractional bit.
What letter drill bit is closest to 3/8 inch?
The 3/8 inch bit is 0.3750 inch. The nearest letter bit is V at 0.3770 inch on most charts, and U at 0.3680 inch is slightly smaller.
Do letter and number bits ever overlap?
The number series ends at 0.2280 inch (#1) and the letter series starts at 0.234 inch (A), so they sit end to end with a very small gap.
Explore the whole Calcs family here.
Tell us which value looks off and we will check it against the sources. Report an issue
Tell us what you looked for. Suggest a chart
Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.