Drill and Tap Chart
A drill and tap chart gives the drill bit to use before tapping each thread size. For example, a 1/4-20 thread uses a #7 drill, and an M6 x 1.0 thread uses a 5.0 mm drill.
Last verified October 5, 2026
75% is the usual choice. Use 60% to 65% for tough metals.
Tap drill
1/4-20 UNC at 75% thread
Unified coarse (UNC) tap drills, #1 to 1-1/2 inch
Tap drill is the major diameter minus 0.01299 × percent thread ÷ threads per inch, then the nearest standard drill. * means published charts split between two neighboring drills.
| Thread size | Threads per inch | Major dia. (in) | Tap drill | Drill dia. (in) | Thread at that drill | Close-fit clearance drill | Free-fit clearance drill |
|---|---|---|---|---|---|---|---|
| #1 | 64 | 0.0730 | #53 | 0.0595 | 67% | 48 (0.0760) | 46 (0.0810) |
| #2 | 56 | 0.0860 | #50 | 0.0700 | 69% | 43 (0.0890) | 41 (0.0960) |
| #3 | 48 | 0.0990 | #47 | 0.0785 | 76% | 37 (0.1040) | 35 (0.1100) |
| #4 | 40 | 0.1120 | #43 | 0.0890 | 71% | 32 (0.1160) | 30 (0.1285) |
| #5 | 40 | 0.1250 | #38 | 0.1015 | 72% | 30 (0.1285) | 29 (0.1360) |
| #6 | 32 | 0.1380 | #36 | 0.1065 | 78% | 27 (0.1440) | 25 (0.1495) |
| #8 | 32 | 0.1640 | #29 | 0.1360 | 69% | 18 (0.1695) | 16 (0.1770) |
| #10 | 24 | 0.1900 | #25 | 0.1495 | 75% | 9 (0.1960) | 7 (0.2010) |
| #12 | 24 | 0.2160 | #16 * | 0.1770 | 72% | 2 (0.2210) | 1 (0.2280) |
| 1/4 | 20 | 0.2500 | #7 | 0.2010 | 75% | F (0.2570) | H (0.2660) |
| 5/16 | 18 | 0.3125 | F | 0.2570 | 77% | P (0.3230) | Q (0.3320) |
| 3/8 | 16 | 0.3750 | 5/16 | 0.3125 | 77% | W (0.3860) | X (0.3970) |
| 7/16 | 14 | 0.4375 | U | 0.3680 | 75% | 29/64 (0.4531) | 15/32 (0.4688) |
| 1/2 | 13 | 0.5000 | 27/64 | 0.4219 | 78% | 33/64 (0.5156) | 17/32 (0.5312) |
| 9/16 | 12 | 0.5625 | 31/64 | 0.4844 | 72% | 37/64 (0.5781) | 19/32 (0.5938) |
| 5/8 | 11 | 0.6250 | 17/32 | 0.5312 | 79% | 41/64 (0.6406) | 21/32 (0.6562) |
| 3/4 | 10 | 0.7500 | 21/32 | 0.6562 | 72% | 49/64 (0.7656) | 25/32 (0.7812) |
| 7/8 | 9 | 0.8750 | 49/64 | 0.7656 | 76% | 57/64 (0.8906) | 29/32 (0.9062) |
| 1 | 8 | 1.0000 | 7/8 | 0.8750 | 77% | 1-1/64 (1.0156) | 1-1/32 (1.0312) |
| 1-1/8 | 7 | 1.1250 | 63/64 | 0.9844 | 76% | — | — |
| 1-1/4 | 7 | 1.2500 | 1-7/64 | 1.1094 | 76% | — | — |
| 1-3/8 | 6 | 1.3750 | 1-7/32 | 1.2188 | 72% | — | — |
| 1-1/2 | 6 | 1.5000 | 1-11/32 | 1.3438 | 72% | — | — |
Unified fine (UNF) tap drills, #0 to 1-1/2 inch
| Thread size | Threads per inch | Major dia. (in) | Tap drill | Drill dia. (in) | Thread at that drill | Close-fit clearance drill | Free-fit clearance drill |
|---|---|---|---|---|---|---|---|
| #0 | 80 | 0.0600 | 3/64 | 0.0469 | 81% | 52 (0.0635) | 50 (0.0700) |
| #1 | 72 | 0.0730 | #53 | 0.0595 | 75% | 48 (0.0760) | 46 (0.0810) |
| #2 | 64 | 0.0860 | #50 | 0.0700 | 79% | 43 (0.0890) | 41 (0.0960) |
| #3 | 56 | 0.0990 | #45 | 0.0820 | 73% | 37 (0.1040) | 35 (0.1100) |
| #4 | 48 | 0.1120 | #42 | 0.0935 | 68% | 32 (0.1160) | 30 (0.1285) |
| #5 | 44 | 0.1250 | #37 | 0.1040 | 71% | 30 (0.1285) | 29 (0.1360) |
| #6 | 40 | 0.1380 | #33 | 0.1130 | 77% | 27 (0.1440) | 25 (0.1495) |
| #8 | 36 | 0.1640 | #29 | 0.1360 | 78% | 18 (0.1695) | 16 (0.1770) |
| #10 | 32 | 0.1900 | #21 | 0.1590 | 76% | 9 (0.1960) | 7 (0.2010) |
| #12 | 28 | 0.2160 | #14 * | 0.1820 | 73% | 2 (0.2210) | 1 (0.2280) |
| 1/4 | 28 | 0.2500 | #3 | 0.2130 | 80% | F (0.2570) | H (0.2660) |
| 5/16 | 24 | 0.3125 | I | 0.2720 | 75% | P (0.3230) | Q (0.3320) |
| 3/8 | 24 | 0.3750 | Q | 0.3320 | 79% | W (0.3860) | X (0.3970) |
| 7/16 | 20 | 0.4375 | 25/64 | 0.3906 | 72% | 29/64 (0.4531) | 15/32 (0.4688) |
| 1/2 | 20 | 0.5000 | 29/64 | 0.4531 | 72% | 33/64 (0.5156) | 17/32 (0.5312) |
| 9/16 | 18 | 0.5625 | 33/64 | 0.5156 | 65% | 37/64 (0.5781) | 19/32 (0.5938) |
| 5/8 | 18 | 0.6250 | 37/64 | 0.5781 | 65% | 41/64 (0.6406) | 21/32 (0.6562) |
| 3/4 | 16 | 0.7500 | 11/16 | 0.6875 | 77% | 49/64 (0.7656) | 25/32 (0.7812) |
| 7/8 | 14 | 0.8750 | 13/16 | 0.8125 | 67% | 57/64 (0.8906) | 29/32 (0.9062) |
| 1 | 12 | 1.0000 | 59/64 | 0.9219 | 72% | 1-1/64 (1.0156) | 1-1/32 (1.0312) |
| 1-1/8 | 12 | 1.1250 | 1-3/64 | 1.0469 | 72% | — | — |
| 1-1/4 | 12 | 1.2500 | 1-11/64 | 1.1719 | 72% | — | — |
| 1-3/8 | 12 | 1.3750 | 1-19/64 | 1.2969 | 72% | — | — |
| 1-1/2 | 12 | 1.5000 | 1-27/64 | 1.4219 | 72% | — | — |
Metric coarse tap drills, M1 to M30
Tap drill is the major diameter minus 1.299 × pitch × percent thread.
| Thread | Pitch (mm) | Major dia. (mm) | Tap drill (mm) | Thread at that drill | Close clearance (mm) | Medium clearance (mm) | Free clearance (mm) |
|---|---|---|---|---|---|---|---|
| M1 | 0.25 | 1 | 0.75 | 77% | — | — | — |
| M1.1 | 0.25 | 1.1 | 0.85 | 77% | — | — | — |
| M1.2 | 0.25 | 1.2 | 0.95 | 77% | — | — | — |
| M1.4 | 0.3 | 1.4 | 1.1 | 77% | — | — | — |
| M1.6 | 0.35 | 1.6 | 1.25 | 77% | 1.7 | 1.8 | 2 |
| M1.8 | 0.35 | 1.8 | 1.45 | 77% | — | — | — |
| M2 | 0.4 | 2 | 1.6 | 77% | 2.2 | 2.4 | 2.6 |
| M2.2 | 0.45 | 2.2 | 1.75 | 77% | — | — | — |
| M2.5 | 0.45 | 2.5 | 2.05 | 77% | 2.7 | 2.9 | 3.1 |
| M3 | 0.5 | 3 | 2.5 | 77% | 3.2 | 3.4 | 3.6 |
| M3.5 | 0.6 | 3.5 | 2.9 | 77% | — | — | — |
| M4 | 0.7 | 4 | 3.3 | 77% | 4.3 | 4.5 | 4.8 |
| M4.5 | 0.75 | 4.5 | 3.7 | 82% | — | — | — |
| M5 | 0.8 | 5 | 4.2 | 77% | 5.3 | 5.5 | 5.8 |
| M6 | 1 | 6 | 5 | 77% | 6.4 | 6.6 | 7 |
| M7 | 1 | 7 | 6 | 77% | — | — | — |
| M8 | 1.25 | 8 | 6.8 | 74% | 8.4 | 9 | 10 |
| M9 | 1.25 | 9 | 7.8 | 74% | — | — | — |
| M10 | 1.5 | 10 | 8.5 | 77% | 10.5 | 11 | 12 |
| M11 | 1.5 | 11 | 9.5 | 77% | — | — | — |
| M12 | 1.75 | 12 | 10.2 | 79% | 13 | 13.5 | 14.5 |
| M14 | 2 | 14 | 12 | 77% | 15 | 15.5 | 16.5 |
| M16 | 2 | 16 | 14 | 77% | 17 | 17.5 | 18.5 |
| M18 | 2.5 | 18 | 15.5 | 77% | 19 | 20 | 21 |
| M20 | 2.5 | 20 | 17.5 | 77% | 21 | 22 | 24 |
| M22 | 2.5 | 22 | 19.5 | 77% | 23 | 24 | 26 |
| M24 | 3 | 24 | 21 | 77% | 25 | 26 | 28 |
| M27 | 3 | 27 | 24 | 77% | 28 | 30 | 32 |
| M30 | 3.5 | 30 | 26.5 | 77% | 31 | 33 | 35 |
Metric fine tap drills
Only the fine pitches listed by at least two sources.
| Thread | Pitch (mm) | Major dia. (mm) | Tap drill (mm) | Thread at that drill | Close clearance (mm) | Medium clearance (mm) | Free clearance (mm) |
|---|---|---|---|---|---|---|---|
| M4x0.5 | 0.5 | 4 | 3.5 | 77% | 4.3 | 4.5 | 4.8 |
| M5x0.5 | 0.5 | 5 | 4.5 | 77% | 5.3 | 5.5 | 5.8 |
| M6x0.75 | 0.75 | 6 | 5.25 | 77% | 6.4 | 6.6 | 7 |
| M8x1 | 1 | 8 | 7 | 77% | 8.4 | 9 | 10 |
| M8x0.75 | 0.75 | 8 | 7.25 | 77% | 8.4 | 9 | 10 |
| M10x1.25 | 1.25 | 10 | 8.8 | 74% | 10.5 | 11 | 12 |
| M10x1 | 1 | 10 | 9 | 77% | 10.5 | 11 | 12 |
| M10x0.75 | 0.75 | 10 | 9.25 | 77% | 10.5 | 11 | 12 |
| M12x1.5 | 1.5 | 12 | 10.5 | 77% | 13 | 13.5 | 14.5 |
| M12x1.25 | 1.25 | 12 | 10.8 | 74% | 13 | 13.5 | 14.5 |
| M12x1 | 1 | 12 | 11 | 77% | 13 | 13.5 | 14.5 |
| M14x1.5 | 1.5 | 14 | 12.5 | 77% | 15 | 15.5 | 16.5 |
| M14x1.25 | 1.25 | 14 | 12.8 | 74% | 15 | 15.5 | 16.5 |
| M16x1.5 | 1.5 | 16 | 14.5 | 77% | 17 | 17.5 | 18.5 |
| M18x1.5 | 1.5 | 18 | 16.5 | 77% | 19 | 20 | 21 |
| M20x2 | 2 | 20 | 18 | 77% | 21 | 22 | 24 |
| M20x1.5 | 1.5 | 20 | 18.5 | 77% | 21 | 22 | 24 |
| M22x1.5 | 1.5 | 22 | 20.5 | 77% | 23 | 24 | 26 |
| M24x2 | 2 | 24 | 22 | 77% | 25 | 26 | 28 |
| M24x1.5 | 1.5 | 24 | 22.5 | 77% | 25 | 26 | 28 |
| M27x2 | 2 | 27 | 25 | 77% | 28 | 30 | 32 |
| M30x2 | 2 | 30 | 28 | 77% | 31 | 33 | 35 |
NPT pipe thread tap drills
Tapered pipe threads. The tap drill leaves stock for the taper reamer or tap to finish. Where charts disagree we show the most-cited value first and list the others.
| NPT size | Threads per inch | Pipe OD (in) | Tap drill | Other values published |
|---|---|---|---|---|
| 1/16 | 27 | 0.3125 | C | D (Theoretical Machinist); 1/4 (Eagle Fittings) |
| 1/8 | 27 | 0.4050 | Q | 21/64 (Engineering ToolBox); R (Newman Tools); 21/64 (Eagle Fittings) |
| 1/4 | 18 | 0.5400 | 7/16 | 27/64 (Engineering ToolBox) |
| 3/8 | 18 | 0.6750 | 9/16 | 37/64 (Newman Tools) |
| 1/2 | 14 | 0.8400 | 45/64 | 11/16 (Engineering ToolBox); 23/32 (Newman Tools); 11/16 (Eagle Fittings) |
| 3/4 | 14 | 1.0500 | 29/32 | 59/64 (Newman Tools); 7/8 (Eagle Fittings) |
| 1 | 11.5 | 1.3150 | 1-9/64 | 1-1/8 (Engineering ToolBox); 1-5/32 (Newman Tools); 1-3/32 (Eagle Fittings) |
| 1-1/4 | 11.5 | 1.6600 | 1-31/64 | 1-15/32 (Engineering ToolBox); 1-1/2 (Newman Tools); 1-13/32 (Eagle Fittings) |
| 1-1/2 | 11.5 | 1.9000 | 1-23/32 | 1-47/64 (Theoretical Machinist, Newman Tools); 1-5/8 (Eagle Fittings) |
| 2 | 11.5 | 2.3750 | 2-7/32 | 2-13/64 (Theoretical Machinist); 2-3/16 (Engineering ToolBox); 2-1/32 (Eagle Fittings) |
| 2-1/2 | 8 | 2.8750 | 2-5/8 | 2-9/16 (Engineering ToolBox); 2-1/2 (Eagle Fittings) |
| 3 | 8 | 3.5000 | 3-1/4 | 3-3/16 (Engineering ToolBox); 3-1/16 (Eagle Fittings) |
| 4 | 8 | 4.5000 | 4-1/4 | 4-3/16 (Engineering ToolBox); 4-1/16 (Eagle Fittings) |
How to use this chart
Pick your thread series and size in the finder, or find it in the tables below. The tap drill is calculated from the major diameter and the percent of full thread you want, then rounded to the nearest standard bit. The chart also shows the thread you actually get with that bit and the close and free clearance drills for the matching bolt. Use 75% as a starting point, and drop to 60% to 65% for tough metals to protect the tap.
Frequently asked questions
What size drill bit do I use for a 1/4-20 tap?
Use a #7 drill, which is 0.2010 inch. It leaves about 75% of a full thread.
What drill bit do I use for an M6 tap?
Use a 5.0 mm drill for the standard M6 x 1.0 coarse thread.
How is a tap drill size calculated?
For inch threads, tap drill equals major diameter minus 0.01299 times the percent thread divided by threads per inch. For metric threads, it is major diameter minus 1.299 times pitch times percent thread divided by 100. The result is rounded to the nearest standard bit.
Why is 75% thread the usual choice?
A 75% thread is strong enough for nearly all work. Going higher raises the cutting load and the chance of breaking the tap for very little added holding strength.
Why do some charts show a different drill for the same thread?
Rounding the calculated size to the nearest bit sometimes lands between two neighbors. Where published charts split, the table marks the entry with an asterisk.
What is the difference between a tap drill and a clearance drill?
A tap drill makes the hole you cut threads into. A clearance drill makes a hole the bolt passes through without threads, so it is larger than the bolt.
Explore the whole Calcs family here.
Tell us which value looks off and we will check it against the sources. Report an issue
Tell us what you looked for. Suggest a chart
Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.