Metric Tap Drill Chart

A metric tap drill is the major diameter minus the pitch, close to it. For M6 x 1.0 that is a 5.0 mm drill, and for M8 x 1.25 it is 6.8 mm.

Last verified October 5, 2026

Download PDF
Tap drill finder

75% is the usual choice. Use 60% to 65% for tough metals.

Tap drill

#7

1/4-20 UNC at 75% thread

Metric coarse tap drill chart, M1 to M30

Drill sizes for 50%, 60%, 75% and 80% thread, with the published tap drill and the thread it gives.

ThreadPitch (mm)Major (mm)Drill for 50% (mm)Drill for 60% (mm)Drill for 75% (mm)Drill for 80% (mm)Published tap drill (mm)Thread at that drill
M10.2510.840.810.760.740.7577%
M1.10.251.10.940.910.860.840.8577%
M1.20.251.21.041.010.960.940.9577%
M1.40.31.41.211.171.111.091.177%
M1.60.351.61.371.331.261.241.2577%
M1.80.351.81.571.531.461.441.4577%
M20.421.741.691.611.581.677%
M2.20.452.21.911.851.761.731.7577%
M2.50.452.52.212.152.062.032.0577%
M30.532.682.612.512.482.577%
M3.50.63.53.113.032.922.882.977%
M40.743.553.453.323.273.377%
M4.50.754.54.013.923.773.723.782%
M50.854.484.384.224.174.277%
M6165.355.225.034.96577%
M7176.356.226.035.96677%
M81.2587.197.036.786.706.874%
M91.2598.198.037.787.707.874%
M101.5109.038.838.548.448.577%
M111.51110.039.839.549.449.577%
M121.751210.8610.6410.3010.1810.279%
M1421412.7012.4412.0511.921277%
M1621614.7014.4414.0513.921477%
M182.51816.3816.0515.5615.4015.577%
M202.52018.3818.0517.5617.4017.577%
M222.52220.3820.0519.5619.4019.577%
M2432422.0521.6621.0820.882177%
M2732725.0524.6624.0823.882477%
M303.53027.7327.2726.5926.3626.577%

Metric fine tap drill chart

Fine pitches listed by at least two sources.

ThreadPitch (mm)Major (mm)Drill for 50% (mm)Drill for 60% (mm)Drill for 75% (mm)Drill for 80% (mm)Published tap drill (mm)Thread at that drill
M4x0.50.543.683.613.513.483.577%
M5x0.50.554.684.614.514.484.577%
M6x0.750.7565.515.425.275.225.2577%
M8x1187.357.227.036.96777%
M8x0.750.7587.517.427.277.227.2577%
M10x1.251.25109.199.038.788.708.874%
M10x11109.359.229.038.96977%
M10x0.750.75109.519.429.279.229.2577%
M12x1.51.51211.0310.8310.5410.4410.577%
M12x1.251.251211.1911.0310.7810.7010.874%
M12x111211.3511.2211.0310.961177%
M14x1.51.51413.0312.8312.5412.4412.577%
M14x1.251.251413.1913.0312.7812.7012.874%
M16x1.51.51615.0314.8314.5414.4414.577%
M18x1.51.51817.0316.8316.5416.4416.577%
M20x222018.7018.4418.0517.921877%
M20x1.51.52019.0318.8318.5418.4418.577%
M22x1.51.52221.0320.8320.5420.4420.577%
M24x222422.7022.4422.0521.922277%
M24x1.51.52423.0322.8322.5422.4422.577%
M27x222725.7025.4425.0524.922577%
M30x223028.7028.4428.0527.922877%

How to use this chart

Find your thread in the coarse or fine table. The columns show the drill for 50%, 60%, 75% and 80% of a full thread, so you can choose a deeper thread for strength or a shallower one for easier tapping. The published tap drill column is the standard bit used with that thread, and the last column shows the thread that bit leaves.

Frequently asked questions

What is the tap drill size for M8 x 1.25?

The standard tap drill is 6.8 mm.

What is the tap drill size for M10 x 1.5?

The standard tap drill is 8.5 mm.

What is the tap drill size for M5?

M5 x 0.8 uses a 4.2 mm drill.

How do I find the tap drill for a metric fine thread?

Use the fine table on this page. The drill is the major diameter minus the fine pitch, close to it, so M10 x 1.0 uses 9.0 mm.

Should I use 75% thread on metric taps?

Yes for most work. The published drills are designed for about 75% to 80% thread. Use a slightly bigger drill for hard metals.

Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.

Last verified October 5, 2026. How we verify explains our two-source rule and what we leave out.

Sources used on this page
  • Fabora
  • Drillbitsworld
  • Rivcut
  • Engineering Toolbox
  • CNC Cookbook
  • 6G Tools
  • Turn2Engineering
  • Component Solutions Group
  • Fuller Fasteners
  • Allied Machine & Engineering
  • Bolt Depot
  • Engineer's Bible
  • TR Fastenings
  • Fractory
  • Albany County Fasteners
  • ISO CNC
  • Mech Codex
  • Want.net
  • Theoretical Machinist
  • Newman Tools
  • Engineering ToolBox