NPT Tap Drill Chart
NPT is a tapered pipe thread, so the tap drill is a little smaller than the pipe size. For 1/8 NPT it is a Q drill and for 1/4 NPT it is 7/16 inch.
Last verified October 5, 2026
75% is the usual choice. Use 60% to 65% for tough metals.
Tap drill
1/4-20 UNC at 75% thread
NPT tap drill chart
Where charts disagree we show the most-cited value first and list the others.
| NPT size | Threads per inch | Pipe OD (in) | Tap drill | Other values published |
|---|---|---|---|---|
| 1/16 | 27 | 0.3125 | C | D (Theoretical Machinist); 1/4 (Eagle Fittings) |
| 1/8 | 27 | 0.4050 | Q | 21/64 (Engineering ToolBox); R (Newman Tools); 21/64 (Eagle Fittings) |
| 1/4 | 18 | 0.5400 | 7/16 | 27/64 (Engineering ToolBox) |
| 3/8 | 18 | 0.6750 | 9/16 | 37/64 (Newman Tools) |
| 1/2 | 14 | 0.8400 | 45/64 | 11/16 (Engineering ToolBox); 23/32 (Newman Tools); 11/16 (Eagle Fittings) |
| 3/4 | 14 | 1.0500 | 29/32 | 59/64 (Newman Tools); 7/8 (Eagle Fittings) |
| 1 | 11.5 | 1.3150 | 1-9/64 | 1-1/8 (Engineering ToolBox); 1-5/32 (Newman Tools); 1-3/32 (Eagle Fittings) |
| 1-1/4 | 11.5 | 1.6600 | 1-31/64 | 1-15/32 (Engineering ToolBox); 1-1/2 (Newman Tools); 1-13/32 (Eagle Fittings) |
| 1-1/2 | 11.5 | 1.9000 | 1-23/32 | 1-47/64 (Theoretical Machinist, Newman Tools); 1-5/8 (Eagle Fittings) |
| 2 | 11.5 | 2.3750 | 2-7/32 | 2-13/64 (Theoretical Machinist); 2-3/16 (Engineering ToolBox); 2-1/32 (Eagle Fittings) |
| 2-1/2 | 8 | 2.8750 | 2-5/8 | 2-9/16 (Engineering ToolBox); 2-1/2 (Eagle Fittings) |
| 3 | 8 | 3.5000 | 3-1/4 | 3-3/16 (Engineering ToolBox); 3-1/16 (Eagle Fittings) |
| 4 | 8 | 4.5000 | 4-1/4 | 4-3/16 (Engineering ToolBox); 4-1/16 (Eagle Fittings) |
How to use this chart
Find the NPT size in the first column and read across for threads per inch, pipe outside diameter and tap drill. Charts do not always agree on NPT tap drills, so where we found different values the most-cited one is shown first and the others are listed in the last column. Use a taper reamer or a taper tap to finish the thread.
Frequently asked questions
What drill size do I use for a 1/4 NPT tap?
7/16 inch is the most-cited tap drill for 1/4 NPT. One chart lists 27/64 inch instead.
What drill size do I use for a 1/8 NPT tap?
A Q drill, which is 0.3320 inch, is the most-cited tap drill for 1/8 NPT. Some charts list 21/64 inch (0.3281 inch) instead.
Why do NPT tap drill charts disagree?
Pipe threads are tapered, and the hole has to leave stock for the taper to cut. Different makers pick slightly different drills depending on the tap and the material.
Do I need a special tap for NPT?
Yes. NPT taps are tapered and cut a thread that tightens as it goes in. A straight tap will not make a sealing pipe thread.
Is NPT the same as BSP?
No. NPT has a 60 degree thread angle and BSP has a 55 degree angle, and the pitches differ, so they are not interchangeable.
Explore the whole Calcs family here.
Tell us which value looks off and we will check it against the sources. Report an issue
Tell us what you looked for. Suggest a chart
Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.