Number Drill Bit Sizes
Number drill bits run from #1 (0.2280 in) down to #80 (0.0135 in), and the smaller the diameter, the bigger the number.
Last verified October 5, 2026
Closest bits
0.1990 in (5.05 mm), 0.0010 in under 0.2000 in
Number drill bit sizes, #1 to #80
Each size with the screw threads that use it as a 75% tap drill.
| Size | Decimal (in) | Millimeters | 75% tap drill for |
|---|---|---|---|
| #1 | 0.2280 | 5.79 | — |
| #2 | 0.2210 | 5.61 | — |
| #3 | 0.2130 | 5.41 | 1/4-28 UNF |
| #4 | 0.2090 | 5.31 | — |
| #5 | 0.2055 | 5.22 | — |
| #6 | 0.2040 | 5.18 | — |
| #7 | 0.2010 | 5.11 | 1/4-20 UNC |
| #8 | 0.1990 | 5.05 | — |
| #9 | 0.1960 | 4.98 | — |
| #10 | 0.1935 | 4.92 | — |
| #11 | 0.1910 | 4.85 | — |
| #12 | 0.1890 | 4.80 | — |
| #13 | 0.1850 | 4.70 | — |
| #14 | 0.1820 | 4.62 | #12-28 UNF |
| #15 | 0.1800 | 4.57 | — |
| #16 | 0.1770 | 4.50 | #12-24 UNC |
| #17 | 0.1730 | 4.39 | — |
| #18 | 0.1695 | 4.30 | — |
| #19 | 0.1660 | 4.22 | — |
| #20 | 0.1610 | 4.09 | — |
| #21 | 0.1590 | 4.04 | #10-32 UNF |
| #22 | 0.1570 | 3.99 | — |
| #23 | 0.1540 | 3.91 | — |
| #24 | 0.1520 | 3.86 | — |
| #25 | 0.1495 | 3.80 | #10-24 UNC |
| #26 | 0.1470 | 3.73 | — |
| #27 | 0.1440 | 3.66 | — |
| #28 | 0.1405 | 3.57 | — |
| #29 | 0.1360 | 3.45 | #8-32 UNC, #8-36 UNF |
| #30 | 0.1285 | 3.26 | — |
| #31 | 0.1200 | 3.05 | — |
| #32 | 0.1160 | 2.95 | — |
| #33 | 0.1130 | 2.87 | #6-40 UNF |
| #34 | 0.1110 | 2.82 | — |
| #35 | 0.1100 | 2.79 | — |
| #36 | 0.1065 | 2.71 | #6-32 UNC |
| #37 | 0.1040 | 2.64 | #5-44 UNF |
| #38 | 0.1015 | 2.58 | #5-40 UNC |
| #39 | 0.0995 | 2.53 | — |
| #40 | 0.0980 | 2.49 | — |
| #41 | 0.0960 | 2.44 | — |
| #42 | 0.0935 | 2.38 | #4-48 UNF |
| #43 | 0.0890 | 2.26 | #4-40 UNC |
| #44 | 0.0860 | 2.18 | — |
| #45 | 0.0820 | 2.08 | #3-56 UNF |
| #46 | 0.0810 | 2.06 | — |
| #47 | 0.0785 | 1.99 | #3-48 UNC |
| #48 | 0.0760 | 1.93 | — |
| #49 | 0.0730 | 1.85 | — |
| #50 | 0.0700 | 1.78 | #2-56 UNC, #2-64 UNF |
| #51 | 0.0670 | 1.70 | — |
| #52 | 0.0635 | 1.61 | — |
| #53 | 0.0595 | 1.51 | #1-64 UNC, #1-72 UNF |
| #54 | 0.0550 | 1.40 | — |
| #55 | 0.0520 | 1.32 | — |
| #56 | 0.0465 | 1.18 | — |
| #57 | 0.0430 | 1.09 | — |
| #58 | 0.0420 | 1.07 | — |
| #59 | 0.0410 | 1.04 | — |
| #60 | 0.0400 | 1.02 | — |
| #61 | 0.0390 | 0.99 | — |
| #62 | 0.0380 | 0.96 | — |
| #63 | 0.0370 | 0.94 | — |
| #64 | 0.0360 | 0.91 | — |
| #65 | 0.0350 | 0.89 | — |
| #66 | 0.0330 | 0.84 | — |
| #67 | 0.0320 | 0.81 | — |
| #68 | 0.0310 | 0.79 | — |
| #69 | 0.0292 | 0.74 | — |
| #70 | 0.0280 | 0.71 | — |
| #71 | 0.0260 | 0.66 | — |
| #72 | 0.0250 | 0.64 | — |
| #73 | 0.0240 | 0.61 | — |
| #74 | 0.0225 | 0.57 | — |
| #75 | 0.0210 | 0.53 | — |
| #76 | 0.0200 | 0.51 | — |
| #77 | 0.0180 | 0.46 | — |
| #78 | 0.0160 | 0.41 | — |
| #79 | 0.0145 | 0.37 | — |
| #80 | 0.0135 | 0.34 | — |
How to use this chart
Find the number you have and read across to inches and millimeters. The last column shows the screw threads that use that bit as a 75% tap drill, so it doubles as a quick tap drill lookup. The nearest-size finder works with any measurement and lists the closest number bit along with the other series.
Frequently asked questions
What is a #7 drill bit in inches?
A #7 bit is 0.2010 inch, or 5.11 mm. It is the standard tap drill for a 1/4-20 thread.
What size is a #10 drill bit?
A #10 bit is 0.1935 inch, or about 4.9 mm.
Why do number drill bits get smaller as the number goes up?
The numbers come from an old wire gauge system, where a higher gauge meant a thinner wire. Drill sizes kept the same direction.
Which number drill bit is closest to 1/8 inch?
The 1/8 inch bit is 0.1250 inch. The nearest number bit is #30 at 0.1285 inch, which is 0.0035 inch over. A #31 is 0.1200 inch, which is 0.0050 inch under.
Are number drill bits used for tapping?
Yes. Small screws such as #4 through #10 use number bits as tap drills. The last column on this page shows which thread each bit tapped at 75% thread.
Explore the whole Calcs family here.
Tell us which value looks off and we will check it against the sources. Report an issue
Tell us what you looked for. Suggest a chart
Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.