Fractional Drill Bit Sizes

Fractional drill bits step up in 1/64 inch, from 1/64 inch (0.0156 in) to 1 inch.

Last verified October 5, 2026

Download PDF
Nearest drill size

Closest bits

#8

0.1990 in (5.05 mm), 0.0010 in under 0.2000 in

True-size drill panel Print at 100% (no scaling). The bar below is exactly one inch.
1/64
1/32
3/64
1/16
5/64
3/32
7/64
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
17/64
9/32
19/64
5/16
21/64
11/32
23/64
3/8
25/64
13/32
27/64
7/16
29/64
15/32
31/64
1/2
1 inch

Fractional drill bit sizes, 1/64 to 1 inch

Each size with the screw thread that uses it as a 75% tap drill, where one does.

SizeDecimal (in)Millimeters75% tap drill for
1/640.01560.40—
1/320.03120.79—
3/640.04691.19#0-80 UNF
1/160.06251.59—
5/640.07811.98—
3/320.09382.38—
7/640.10942.78—
1/80.12503.17—
9/640.14063.57—
5/320.15623.97—
11/640.17194.37—
3/160.18754.76—
13/640.20315.16—
7/320.21885.56—
15/640.23445.95—
1/40.25006.35—
17/640.26566.75—
9/320.28127.14—
19/640.29697.54—
5/160.31257.943/8-16 UNC
21/640.32818.33—
11/320.34388.73—
23/640.35949.13—
3/80.37509.53—
25/640.39069.927/16-20 UNF
13/320.406210.32—
27/640.421910.721/2-13 UNC
7/160.437511.11—
29/640.453111.511/2-20 UNF
15/320.468811.91—
31/640.484412.309/16-12 UNC
1/20.500012.70—
33/640.515613.109/16-18 UNF
17/320.531213.495/8-11 UNC
35/640.546913.89—
9/160.562514.29—
37/640.578114.685/8-18 UNF
19/320.593815.08—
39/640.609415.48—
5/80.625015.88—
41/640.640616.27—
21/320.656216.673/4-10 UNC
43/640.671917.07—
11/160.687517.463/4-16 UNF
45/640.703117.86—
23/320.718818.26—
47/640.734418.65—
3/40.750019.05—
49/640.765619.457/8-9 UNC
25/320.781219.84—
51/640.796920.24—
13/160.812520.647/8-14 UNF
53/640.828121.03—
27/320.843821.43—
55/640.859421.83—
7/80.875022.231-8 UNC
57/640.890622.62—
29/320.906223.02—
59/640.921923.421-12 UNF
15/160.937523.81—
61/640.953124.21—
31/320.968824.61—
63/640.984425.001-1/8-7 UNC
11.000025.40—

How to use this chart

Find the fraction, then read the decimal and millimeter size. Where a fractional bit is also the tap drill for a common thread, the last column says so. Print the page at 100% to use the true-size panel as a quick visual check against bits you already own.

Frequently asked questions

How do you read a drill bit size in fractions?

The number on top is how many 64ths, 32nds, 16ths and so on. A 5/16 bit is 5 sixteenths of an inch, which is 0.3125 inch.

What is 1/64 of an inch in decimal?

1/64 inch is 0.015625 inch, or 0.397 mm. Each step in the fractional series adds that much.

What is the next size up from a 1/4 inch drill bit?

In the 1/64 series, the next size up is 17/64 inch (0.2656 inch).

What fractional drill bit is closest to 6 mm?

15/64 inch is 5.95 mm, the closest fractional bit under 6 mm. 1/4 inch is 6.35 mm, the closest over.

Do fractional bits come larger than 1 inch?

Yes. Twist bits are made in 1/64 steps up to about 1/2 inch and in larger steps after that. This chart stops at 1 inch.

Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.

Last verified October 5, 2026. How we verify explains our two-source rule and what we leave out.

Sources used on this page
  • Rivcut
  • Victor Technologies/Victornet
  • Fastenal
  • AFT Fasteners drill bit size chart
  • MISUMI USA blog drill bit size chart
  • Victornet