Sheet Metal Gauge Chart

Gauge numbers are not one thickness. A 14 gauge sheet is 0.0747 inch in standard steel, 0.0781 inch in stainless steel and 0.0641 inch in aluminum.

Last verified October 5, 2026

Download PDF
Gauge lookup

Quick lookup

0.2391" steel

3 gauge sheet

Standard steel
0.2391 in (6.07 mm)
Galvanized steel
not published here
Stainless steel
0.2500 in (6.35 mm)
Aluminum
0.2294 in (5.83 mm)

Sheet metal gauge chart, 3 to 36 gauge

A gauge number is not one thickness. The same number means a different thickness in steel, galvanized steel, stainless steel and aluminum, so always check which metal a gauge refers to. A dash means the value did not meet our two-source rule.

GaugeStandard steel (in)Standard steel (mm)Galvanized (in)Galvanized (mm)Stainless (in)Stainless (mm)Aluminum (in)Aluminum (mm)
30.23916.07——0.25006.350.22945.83
40.22425.69——0.23445.950.20435.19
50.20925.31——0.21875.550.18194.62
60.19434.94——0.20315.160.16204.11
70.17934.55——0.18754.760.14433.67
80.16444.18——0.17194.370.12853.26
90.14953.800.15323.890.15623.970.11442.91
100.13453.420.13823.510.14063.570.10192.59
110.11963.040.12333.130.12503.170.09072.30
120.10462.660.10842.750.10942.780.08082.05
130.08972.280.09342.370.09372.380.07201.83
140.07471.900.07851.990.07811.980.06411.63
150.06731.710.07101.800.07031.790.05711.45
160.05981.520.06351.610.06251.590.05081.29
170.05381.370.05751.460.05621.430.04531.15
180.04781.210.05161.310.05001.270.04031.02
190.04181.060.04561.160.04371.110.03590.91
200.03590.910.03961.010.03750.950.03200.81
210.03290.840.03660.930.03440.870.02850.72
220.02990.760.03360.850.03120.790.02530.64
230.02690.680.03060.780.02810.710.02260.57
240.02390.610.02760.700.02500.640.02010.51
250.02090.530.02470.630.02190.560.01790.45
260.01790.450.02170.550.01870.470.01590.40
270.01640.420.02020.510.01720.440.01420.36
280.01490.380.01870.470.01560.400.01260.32
290.01350.340.01720.440.01410.360.01130.29
300.01200.300.01570.400.01250.320.01000.25
310.01050.27————0.00890.23
320.00970.25————0.00800.20
330.00900.23————0.00710.18
340.00820.21————0.00630.16
350.00750.19————0.00560.14
360.00670.17——————

How to use this chart

Pick the metal, find the gauge number and read the thickness in inches and millimeters. The same gauge means a different thickness in each metal, so always check the metal first. A dash means the value did not meet our two-source rule. Use calipers to check sheet you already have.

Frequently asked questions

What is 14 gauge steel in inches?

0.0747 inch, or 1.90 mm, for standard steel sheet.

What is 16 gauge steel in inches?

0.0598 inch, or 1.52 mm.

What is 18 gauge steel in inches?

0.0478 inch, or 1.21 mm.

Why is a smaller gauge number thicker?

Gauge numbers are commonly traced to how many times wire was drawn to thin it, so more draws meant a higher number and thinner metal. Sheet gauges kept the same direction.

Is galvanized steel thicker than plain steel at the same gauge?

Yes, slightly, because of the zinc coating. At 14 gauge, galvanized is 0.0785 inch against 0.0747 inch for standard steel.

How do I measure sheet metal gauge?

Measure the thickness with calipers or a micrometer, then find the closest match in the column for your metal.

Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.

Last verified October 5, 2026. How we verify explains our two-source rule and what we leave out.

Sources used on this page
  • Archtoolbox
  • CustomPartNet
  • All Points Fasteners
  • Riverside Sheet Metal
  • Welders Supply
  • RAM Steel Co
  • Engineering Toolbox