Aluminum Sheet Metal Gauge Chart

Aluminum sheet follows the Brown and Sharpe (AWG) scale, so it is thinner than steel at the same gauge. At 14 gauge, aluminum is 0.0641 inch against 0.0747 inch for steel.

Last verified October 5, 2026

Download PDF
Gauge lookup

Quick lookup

0.2391" steel

3 gauge sheet

Standard steel
0.2391 in (6.07 mm)
Galvanized steel
not published here
Stainless steel
0.2500 in (6.35 mm)
Aluminum
0.2294 in (5.83 mm)

Aluminum sheet metal gauge chart, 3 to 35 gauge

Aluminum uses the Brown and Sharpe (AWG) scale. A gauge number is not one thickness. The same number means a different thickness in steel, galvanized steel, stainless steel and aluminum, so always check which metal a gauge refers to. A dash means the value did not meet our two-source rule.

GaugeAluminum (in)Aluminum (mm)Standard steel (in)Standard steel (mm)
30.22945.830.23916.07
40.20435.190.22425.69
50.18194.620.20925.31
60.16204.110.19434.94
70.14433.670.17934.55
80.12853.260.16444.18
90.11442.910.14953.80
100.10192.590.13453.42
110.09072.300.11963.04
120.08082.050.10462.66
130.07201.830.08972.28
140.06411.630.07471.90
150.05711.450.06731.71
160.05081.290.05981.52
170.04531.150.05381.37
180.04031.020.04781.21
190.03590.910.04181.06
200.03200.810.03590.91
210.02850.720.03290.84
220.02530.640.02990.76
230.02260.570.02690.68
240.02010.510.02390.61
250.01790.450.02090.53
260.01590.400.01790.45
270.01420.360.01640.42
280.01260.320.01490.38
290.01130.290.01350.34
300.01000.250.01200.30
310.00890.230.01050.27
320.00800.200.00970.25
330.00710.180.00900.23
340.00630.160.00820.21
350.00560.140.00750.19

How to use this chart

Find the gauge number and read the aluminum thickness in inches and millimeters. Standard steel is listed next to it, because the same gauge is a different thickness in each metal. Check the thickness with calipers if the part matters, since mills may list sheet by decimal thickness.

Frequently asked questions

What is 16 gauge aluminum in inches?

0.0508 inch, or 1.29 mm.

What is 18 gauge aluminum in inches?

0.0403 inch, or 1.02 mm.

What is 14 gauge aluminum in inches?

0.0641 inch, or 1.63 mm.

Why is aluminum thinner than steel at the same gauge?

Aluminum uses the Brown and Sharpe scale, which is the same as AWG for wire, while steel uses a different gauge table.

Do aluminum suppliers sell by gauge?

Many sell by decimal thickness instead, so look for the thickness in inches, such as 0.040 or 0.063.

Disclaimer. Reference values for information only. Check the manufacturer's data for your part. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.

Last verified October 5, 2026. How we verify explains our two-source rule and what we leave out.

Sources used on this page
  • Archtoolbox
  • CustomPartNet
  • All Points Fasteners
  • Riverside Sheet Metal
  • Welders Supply
  • RAM Steel Co
  • Engineering Toolbox