Propane Pipe Sizing Chart

Propane carries more heat per cubic foot than natural gas, so smaller pipe will do. For example, 3/4 inch steel carries about 259 MBH over 50 feet and 1 inch carries about 488 MBH, at a 0.5 inch water column drop.

Last verified October 5, 2026

Important. Estimate only. Gas piping must be sized, installed and inspected by a licensed professional under your local code and the appliance maker's instructions.

Download PDF
Gas pipe sizing calculator

Smallest pipe that meets the load

1 inch

Propane pipe sizing chart, steel, 0.5 in. w.c. drop

Sizing equation for low-pressure systems: D = Q0.381 ÷ (19.17 × (ΔH ÷ (Cr × L))0.206), where D is inside diameter in inches, Q is flow in cubic feet per hour, ΔH is the pressure drop in inches of water column, L is the pipe length in feet and Cr is 0.6094 for natural gas or 1.2462 for propane. Capacities below invert the same equation and are shown in thousands of BTU per hour. Natural gas is taken at 1,000 BTU per cubic foot and propane at 2,516.

Propane, Schedule 40 steel, MBH
Pipe length1/2"3/4"1"1-1/4"1-1/2"2"2-1/2"3"4"
10 ft2966191,1662,3943,5886,91411,02319,49339,778
20 ft2034258011,6462,4674,7537,57713,40027,345
30 ft1633426441,3221,9813,8176,08610,76221,962
40 ft1402925511,1321,6963,2675,2099,21218,798
50 ft1242594881,0031,5032,8964,6178,16516,662
60 ft1122354429091,3622,6244,1847,39915,098
80 ft962013797781,1662,2463,5816,33312,923
100 ft851783366891,0331,9913,1745,61311,454
125 ft751582986119161,7652,8134,97510,152
150 ft681432705548301,5992,5494,5089,199
200 ft591222314747101,3692,1823,8597,874

Propane, type K copper tube, 0.5 in. w.c. drop

Propane, type K copper tube, MBH
Pipe length3/8"1/2"5/8"3/4"1"1-1/4"1-1/2"2"
10 ft941913354751,0151,8272,8826,005
20 ft651322303266981,2561,9814,128
30 ft521061852625601,0091,5913,316
40 ft44901582244808641,3622,838
50 ft39801401994257651,2072,515
60 ft36731271803856941,0942,279
80 ft31621091543305949361,951
100 ft2755961372925268301,729
125 ft2449851212594667361,533
150 ft2244771102354236671,389
200 ft193866942013625701,189

Propane, Schedule 40 steel, 1.0 in. w.c. drop

Propane, Schedule 40 steel, 1.0 in. w.c., MBH
Pipe length1/2"3/4"1"1-1/4"1-1/2"2"2-1/2"3"4"
10 ft4309001,6963,4835,22010,05716,03428,35657,863
20 ft2966191,1662,3943,5886,91411,02319,49339,778
30 ft2374979361,9232,8825,5538,85315,65631,947
40 ft2034258011,6462,4674,7537,57713,40027,345
50 ft1803777101,4592,1864,2136,71611,87724,237
60 ft1633426441,3221,9813,8176,08610,76221,962
80 ft1402925511,1321,6963,2675,2099,21218,798
100 ft1242594881,0031,5032,8964,6178,16516,662
125 ft1102304338891,3322,5674,0927,23714,768
150 ft992083928051,2072,3263,7086,55813,382
200 ft851783366891,0331,9913,1745,61311,454

How to use this chart

Find the pipe length in the first column and read across to each pipe size for capacity in thousands of BTU per hour. Add up the BTU of your appliances and pick a size that carries the total at the length of your longest run. These values are for low-pressure systems. Always round up and have a licensed professional size the system.

Frequently asked questions

What size propane line do I need?

It depends on the load and the length. Use the calculator to size a run, and the table here to check it.

How much propane will 1/2 inch pipe carry?

About 203 MBH over 20 feet at a 0.5 inch water column drop.

Is propane piping different from natural gas piping?

The materials are the same, but propane has a higher heating value, so a given pipe carries more BTU. Pressures and regulators are different too.

How many BTU in a cubic foot of propane?

About 2,516 BTU per cubic foot, against about 1,000 for natural gas.

Can I use these tables for the line between the tank and the regulator?

No. High-pressure lines use different tables. These values are for low-pressure lines after the regulator.

Disclaimer. Estimate only. Gas piping must be sized, installed and inspected by a licensed professional under your local code and the appliance maker's instructions. Charts & Specs is an independent reference site. It is not affiliated with any manufacturer, standards body or code organization, and it uses brand and standard names only to identify what a value applies to.

Last verified October 5, 2026. How we verify explains our two-source rule and what we leave out.

The pipe-sizing constants (Cr of 0.6094 for natural gas and 1.2462 for propane, and the 0.381, 0.206 and 19.17 terms) were checked in the adopted fuel gas code text as reproduced by Seattle and the ICC. Those copies come from the same code text, so they are one source seen several times, not independent confirmation.

Sources used on this page
  • Seattle fuel gas code, chapter 4 (adopted IFGC text)
  • ICC-hosted IFGC chapter 4
  • H2X Engineering calculator
  • PHCP Pros
  • Copper Development Association tube tables
  • Wheatland Tube ASTM A53 pipe table
  • Engineering ToolBox